Metal detector BLISSTOOL LTC64X (THE BEAST) v6 is THE BEST DEEP DETECTING in the ground series produced metal detector on the planet, type no resonance, induction balance, available on the market.
From this type, in parameter depth of detection in the ground, immediately after it are: v5, v4, v3, v2i and v2. In this parameter, in general, after them are all other metal detectors from this type of other brands.
In addition, v6 is with great versatility, all-terrain detector, as achieve excellent results on any type of terrain: low, medium and highly mineralized, unpolluted and contaminated terrains.
v6 is not a toy for kids. v6 is intended for the best and most experienced searchers on the planet!
Well... that's all.
06.12.2015, Slashten, Bulgaria.
Ahmed Merchev
(President, founder, owner and chief developer of BLISSTOOL)
BLISSTOOL
www.blisstool.com
info@blisstool.com
+359883450667
Statistics: Posted by BLISSTOOL — Sun Dec 06, 2015 3:13 pm
]]>
This article contains guidelines for correct ground balance and setting of metal detector BLISSTOOL LTC64X (THE BEAST), as for illustration and a better understanding of the matter, are described some common user errors in this area.
This material is intended mainly for users who are already familiar and have experience with THE BEAST. The beginners should first get acquainted with the user guide of THE BEAST.
The combination: "GAIN=MAX + FRUQUENCY=MIN (TURBO/BOOST mode)" is suitable only for low to medium mineralized soils and only when they are DRY. This combination in WET soils, and/or in medium or highly mineralized soils and/or in soils saturated with large amounts of salts, can lead to an overload of the electronics, which can results in a dulling and partial or full rejection of the signal from some non-ferrous objects.
It should not be forgotten that if soon there was rain, etc., even the surface soil is dry, in depth (which usually are the metal objects) it is probably still wet.
Common mistakes is when the user can not easily make ground balance or when it is objectively not possible to make ground balance of the detector, to adjust GROUND COARSE in medium setting or close to it, or with setting for ground balance to ferrite. Where is the mistake? The error in this case is that your BLISSTOOL detector tells you, actually screams, figuratively speaking, something like this: "Buddy, your settings of GAIN, FREQUENCY and THRESHOLD (written on the degree of influence of the strong to the weak), are too high and impossible for this soil. Please reduce them to facilitate the work of both of us and will have no care". Instead, some users set GROUND COARSE at their discretion and apply different tricks (mostly wrong for the case) to cause the detector to work with these impossible settings for this soil. And yes, THE BEAST continues to work, but not in the best way, which in some cases may be far from optimal, for example in highly mineralized soils and in soils saturated with large amounts of salts.
Also must not forget that:
- For hot rocks and soils, containing ferrous metals and their oxides (for example: iron and iron oxides), the manual ground balance is done in mode "All metal", i.e. with off discrimination of the metal detector (DISCR LEVEL = 0, DISCR DEPTH = 0). After the manual ground balancing on the hot rock, are set the user-selected levels of discrimination (for example: DISCR LEVEL = 4 - 5, DISCR DEPTH = 8.5 - 9.0).
- For hot rocks and soils containing non-ferrous metals and their oxides, because of their presence, usually manual ground balance in mode "All metal", i.e. with off discrimination of the metal detector (DISCR LEVEL = 0, DISCR DEPTH = 0) is not possible. In this case, the manual ground balance is performed with prior set discrimination of the metal detector (for example: DISCR LEVEL = 4 - 5, DISCR DEPTH = 8.5 - 9.0).
It is important to know this in situations where there is difficulty with the ground balance, even at low levels of GAIN.
The TURBO/BOOST mode of THE BEAST is designed to be completely stable and some users use switching from mode NORMAL (FREQUENCY=MAX) to mode TURBO/BOOST (FREQUENCY=MIN) to stabilize the detector at high setting of GAIN, but this is the wrong practice, especially in wet soil. Proper practice is to decrease the GAIN level.
Furthermore, with a random medium setting of GROUND COARSE, is permitted to work only at low mineralized soils. On medium or highly mineralized soils, is necessarily (strictly required), to make individual fine-tune ground balance setting to the soil.
The correct ground balance, in addition to ensuring stability and lack of false signals, provides correct discrimination (identification). In incorrect ground balance, the error signal from the ground (the soil) is summed with the signal from the target (the metal object), leading to incorrect identification (discrimination). This is particularly evident at medium and highly mineralized soils (they achieved ground balance at levels of GROUND COARSE = 5-8) and in soils saturated with large amounts of salts (they achieved ground balance at low levels of GROUND COARSE = 2-4), or in infinite possible combination of the two.
Also must not forget, that after each change of the setting of GAIN and/or FREQUENCY, is strictly required to make a new ground balance.
The soils saturated with large amounts of salts, are biggest trap, especially for beginners, because although they seem harmless at first glance, given that most of them are low or medium mineralized (soils with low or medium content of metals and metal oxides) and allow work at relatively wide range of settings, they require fine tuning of the ground balance and work with lower levels of discrimination (levels lower than the standard used). Otherwise, can cause to blinding of the signal from non-ferrous objects as ferrous, which effect is available also in high mineralized soils (soils with high content of metals and metal oxides). Unlike them, however, the soils saturated with large amounts of salts, visible, are a big problem, only when they are wet.
Also, in all problematic/complex soils, after ground balance in the conventional manner by vertical movements, it is necessary to check for false signals with horizontal movements and if need to adjust the level of GROUND COARSE with about +- 0.5 - 1.0 level, up to disappearance of the false signals. This additional setting provides better working of the automatic stabilizers available in THE BEAST v4, v5 and v6 and is essential in wet soils and at higher levels of GAIN.
Statistics: Posted by BLISSTOOL — Thu Oct 01, 2015 9:27 pm
]]>
Direct links:
Furthermore, it is already available and a Greek version of the user guide. Direct link:
IMPORTANT: These latest English, Bulgarian and Greek versions of the user guide, contain detailed information, including for v4, v5 and v6 of THE BEAST, so we recommend you to review them.
We hope that this is helpful to you.
Here is also direct link to the Russian version of the user guide:
The latest versions of all user guides for metal detector BLISSTOOL LTC64X (THE BEAST), are available on .
Best Regards,
Ahmed Merchev
(President, sole owner and chief developer of BLISSTOOL)
Statistics: Posted by BLISSTOOL — Thu May 14, 2015 12:19 am
]]>
Current users who have already bought v5, do not have to go to the v6 because with medium levels of setting, v6 has parameters very similar to v5.
In addition, for new customers which are beginners, intermediate and even experienced users, we again recommended v5 or v4, not v6.
Most importantly: v6 is recommended only for VERY EXPERIENCED users, which have the necessary knowledge and skills to make the most of the power of THE BEAST v6 and which want to have the BLISSTOOL metal detector with the best depth of detection until now.
Everyone who passes directly to v6, without having the necessary knowledge for it will make a mistake. v6 is detector ONLY for VERY EXPERIENCED users.
v4 and v5 remains the detectors suitable for most searchers as before, when v6 is detector only for experts.
v6 provides better work at heavy terrain conditions, such as: highly mineralized terrains, terrains with a high content of ore, highly contaminated with iron terrains, highly mineralized sands, and also better depth of detection at low and medium mineralized terrains, but these parameters can only be achieved with precision adequate setting from users with a very good knowledge for the metal detector and the hobby metal detecting as a whole.
The objective in developing of v6 was to realize in practice the possible theoretical maximum for depth of detection and performance for IB metal detector, not only on low and medium mineralized terrains, but also on highly mineralized terrains, where previous models also perform well. v6, probably provides a possible maximum of all this. With that, v6 is even better competition of pulse induction metal detectors and can be used in very difficult terrain conditions, which was our goal.
v6 is desired and long awaited by many VERY EXPERIENCED users working on very difficult terrain conditions anywhere in the world, but in the hands of the same VERY EXPERIENCED users v6 is unsurpassed also on low and medium mineralized terrains and this makes it even more attractive.
To realize this, v6 has two separate modes: mode ORE and mode SOIL and from my perspective as a developer of it, it is a real jewel for experts, but for most searchers, the favorite remains the v5, which we recommend.
Currently the situation is somewhat embarrassing, as far any later version was better for all users, but now with v6 the things are different, as it provides maximum that can be used in practice only from VERY EXPERIENCED users. We had a similar situation at the initial presentation of v3, which was most suitable for intermediate and experienced users, but novice users had some difficulty with it. Smoothly things went with v4 and v5, since they are suitable for beginners, intermediate and experienced users and apparently everyone is happy. We realize this and so do these explanations. No sense to own something if you can not use it well. For this, our sincere recommendation to our current customers is to focus and not to underestimate the version of THE BEAST they have, since any of it provides much, too much. When the time comes for them to switch to a new version of an objective need, they themselves will understand this precise moment for themselves.
Enjoy THE BEAST!
Best Regards,
Ahmed Merchev
(President, sole owner and chief developer of BLISSTOOL)
Statistics: Posted by BLISSTOOL — Mon Dec 01, 2014 12:41 pm
]]>
DETAILED REPORT for the improvements and the new features of v6 of BLISSTOOL LTC64X (THE BEAST).
IMPORTANT: This article contains extensive information about all the improvements and new features of v6 of BLISSTOOL LTC64X (THE BEAST). If you are interested in v6, it is strongly recommended to get acquainted in detail with all the information available below.
Although in appearance, all versions of BLISSTOOL LTC64X (THE BEAST) look the same, they have significant differences in their characteristics: depth of detection, stability, discrimination, basic behavior. Therefore, each version must be considered for a different model metal detector, not a upgrade of the previous version.
The improvements and the new features of v6 of BLISSTOOL LTC64X (THE BEAST), are:
LTC64X v6 is better than v5, with that this LTC64X v6 is:
- with improved work at highly mineralized terrains, terrains with a high content of ore, beach search (on the coast, moist soil, dry sand, wet sand, mineralized sands);
- with mode ORE, optimized for wotk at highly mineralized terrains, terrains with a high content of ore, terrains dotted with hot rocks and stones, highly contaminated with iron terrains, beach search in highly mineralized sands;
- with mode SOIL, optimized for wotk at low and medium mineralized terrains, terrains dotted with stones and rocks, beach search in low and medium mineralized sands;
- with higher detection speed and higher recovery speed in mode ORE;
- with improved depth of detection and improved comfort when working on any type of terrain;
- with automatic stabilizer with a very high degree of stabilization.
All other base characteristics of v6 are the same as of v5:
- v6 has the same extended range of discrimination (DISCRIMINATOR III, II and I) as v5;
- v6 has mode NORMAL (FREQUENCY = MAX, 8.0KHz) and mode TURBO/BOOST (FREQUENCY = MIN, 7.4KHz) as v5 and v4.
v6 has the same knobs and switches as v5, v4, v3, v2i, v2 and v1, but because of the many improvements and new features of v6, its potentiometers GAIN and GROUND FINE have a dual function, i.e. they have a second, additional function, only available in v6.
Thanks to this second, additional function of potentiometers GAIN and GROUND FINE, at v6, in an elegant way, there is provided a quick and convenient access to the new features available in v6, without the need of adding other knobs and switches.
The main differences in the control and the power of v6 of BLISSTOOL LTC64X (THE BEAST), compared to v5, v4, v3, v2i, v2, v1, are:
[01] Potentiometer GAIN:
- At v5, v4, v3, v2i, v2 and v1, potentiometer GAIN has only one function:
/1/ Set the input AC amplification of the signal from the detected object.
- At v6, potentiometer GAIN has two functions:
/1/ Function identical to its function in v5, v4, v3, v2i, v2 and v1, i.e. set the input AC amplification of the signal from the detected object;
/2/ Switch between mode ORE and mode SOIL: with setting GAIN = MIN, v6 work in mode ORE, but with setting GAIN = from 1 to MAX, v6 work in mode SOIL. The intermediate levels from GAIN = MIN to GAIN = 1, ensure a smooth transition from mode ORE to mode SOIL.
Mode ORE is optimized for work at highly mineralized terrains, terrains with a high content of ore, terrains dotted with hot rocks and stones, highly contaminated with iron terrains, beach search in highly mineralized sands. When working on such terrains, mode ORE provides: better depth of detection, greater stability, higher detection speed, higher recovery speed, greater comfort at search.
Mode SOIL is optimized for wotk at low and medium mineralized terrains, terrains dotted with stones and rocks, beach search in low and medium mineralized sands. When working on such terrains, mode SOIL provides: extreme depth of detection.
In mode SOIL, the maximum depth of detection for a single coin with a diameter 24 mm is 58 cm (22.8") in mode NORMAL and 66 cm (26") in mode TURBO/BOOST, while in mode ORE, the maximum depth of detection for a single coin is about 30 cm, account the purpose of mode ORE, i.e.: work in heavy terrain conditions, at which the work in mode SOIL is impossible or very limited and difficult.
The best depth of detection, highest detection speed and highest recovery speed in mode ORE are achieved when work with settings DISCR DEPTH = 0, DISCR LEVEL = 0 (mode All metals). Therefore, to maintain these parameters, especially under very heavy terrain conditions, it is recommended work exactly with these settings.
In mode ORE, in very difficult terrain conditions, in need of work in discrimination mode, the recommended settings are: DISCR DEPTH = 0, DISCR LEVEL = 10, as a last resort are recommended and settings close to them: DISCR DEPTH = from 0 to 6, DISCR LEVEL = from 0 to 10.
In mode ORE, with settings: DISCR DEPTH = 0, DISCR LEVEL = 10, the metal detector discriminate only in the surface layer, to a depth of about 10 - 15 cm, while maintaining the high depth of detection, detection speed and recovery speed, available with settings DISCR DEPTH = 0, DISCR LEVEL = 0 (mode All metals).
In mode ORE, with settings DISCR DEPTH = 0, DISCR LEVEL = 0 (mode All metals) and with settings: DISCR DEPTH = 0, DISCR LEVEL = 10, BLISSTOOL LTC64X (THE BEAST) v6 as behavior, resembles multi-period pulse induction metal detectors.
Described above settings in mode ORE, with recommended possible lower levels of DISCR DEPTH relate mostly for very heavy terrain conditions, such as: highly mineralized terrains, terrains with a high content of ore, highly mineralized sands. For lighter terrain conditions, in mode ORE, may also be used the standard levels of discrimination (such as settings: DISCR DEPTH = from 7 to 9, DISCR LEVEL = from 3 to 6), which are generally most suitable for mode SOIL.
In mode ORE, to achieve the quality of discrimination available with standard levels of discrimination in mode SOIL, DISCR DEPTH and DISCR LEVEL must be set to higher levels compared to their standard setting in mode SOIL.
In mode SOIL, when work with high levels of GAIN is recommended work at possible lower levels of DISCR DEPTH and DISCR LEVEL and conversely: when work with lower levels of GAIN is admissible and work at higher levels of DISCR DEPTH and DISCR LEVEL.
In mode SOIL, settings GAIN = from 1 to 6 are best suitable for low and medium mineralized terrains, while settings GAIN = from 7 to MAX are only suitable for low mineralized terrains and are recommend only for very experienced users, which through skillful precision setting of the sensitivity of the metal detector (through potentiometers GAIN, THRESHOLD and SILENCER), with this extreme increased amplification at GAIN = from 7 to MAX, can achieve better depth of detection in low mineralized terrains.
At work in manual ground balance mode (GROUND MODE = MAN), after each change of the setting of potentiometer GAIN, need again to be made manual ground balance of the metal detector (from potentiometer GROUND COARSE in mode ORE and from potentiometers GROUND COARSE and GROUND FINE in mode SOIL).
[02] Potentiometer GROUND FINE:
- At v5, v4, v3, v2i, v2 and v1, potentiometer GROUND FINE has only one function:
/1/ Serves as a further fine (precise) setting of the ground balance in a manual ground balance working mode, ie for a fine and complete eliminate of the ground effect at work in a manual ground balance working mode.
- At v6, potentiometer GROUND FINE has two functions:
/1/ Function identical to its function in v5, v4, v3, v2i, v2 and v1, i.e. serves as a further fine (precise) setting of the ground balance in a manual ground balance working mode, ie for a fine and complete eliminate of the ground effect at work in a manual ground balance working mode;
/2/ Set the depth of detection in mode ORE.
In mode ORE (GAIN = MIN), the depth of detection is the lowest at GROUND FINE = ''-'' and the greatest at GROUND FINE = ''+'', i.e. with each higher level of GROUND FINE, the depth of detection is better, but greatly increased depth of detection is not recommended for very heavy terrain conditions, because this reducing the detection speed and the recovery speed.
In mode ORE, in heavy terrain conditions, such as: highly mineralized terrains, terrains with a high content of ore, highly mineralized sands, is recomended work with settings GROUND FINE = from 1 to 5.
In mode ORE, BLISSTOOL LTC64X (THE BEAST) v6 has the highest detection speed and the highest recovery speed with settings GROUND FINE = from 1 to 3. Therefore, usually these settings are most suitable for extremely heavy terrain conditions.
In mode ORE, at work in manual ground balance mode (GROUND MODE = MAN), after each change of the setting of potentiometer GROUND FINE, need again to be made manual ground balance of the metal detector (from potentiometer GROUND COARSE).
[03] Switch AUTO ZONES:
Unlike from v5, which has three automatic stabilizers (with low, medium and high level of stabilization), which can be selected by switch AUTO ZONES, v6 has only one automatic stabilizer (with a very high degree of stabilization), as it always work with it, i.e. therefore does not need its switching, switch AUTO ZONES at v6, has only one function, as at v4, v3, v2i, v2 and v1, i.e:
/1/ To set one of the three available automatic ground zones at work in automatic ground balance mode (switch GROUND MODE = AUTO). In manual ground balance mode (switch GROUND MODE = MAN), this function of switch AUTO ZONES not working.
[04] ADDITION about the differences in the depth of detection of the different versions:
In a medium mineralized terrain, the maximum depth of detection of a coin with a diameter 24 mm, for the different versions of BLISSTOOL LTC64X (THE BEAST), with 28 cm (11") DD search coil, is:
- for v2 = 40 cm (15.7")
- for v2i = 43 cm (16.9")
- for v3 = 45 cm (17.7")
- for v4 = 52 cm (20.4") in mode NORMAL / 58 cm (22.8") in mode TURBO/BOOST.
- for v5 = 52 cm (20.4") in mode NORMAL, AUTO ZONES = III / 58 cm (22.8") in mode TURBO/BOOST, AUTO ZONES = III.
- for v6 = 58 cm (22.8") in mode NORMAL / 66 cm (26") in mode TURBO/BOOST.
The maximum depths of detection, described above, are achieved and in SILENT mode of the metal detector, i.e. without audio threshold (THRESHOLD set to level just before the buzz), but with amplification (GAIN) close to the maximum.
In real work underway in medium mineralized terrain, usually the achieved in the practice depths of detection are of the order of 80 - 90% from the maximum depth of detection, described above.
The typical setting of the metal detector, at which are achieved the above described maximum depths of detection, is:
GROUND MODE = MAN
GROUND COARSE = 4 - 6
GROUND FINE = 5
AUTO ZONES = III (only for v5)
GAIN = MAX
THRESHOLD = 6.0 - 6.8
SILENCER = OFF - 2
DISCRIMINATOR = III
DISCR LEVEL = 4 - 5
DISCR DEPTH = 8.0 - 8.5 - 8.8
FREQUENCY = MAX (and also MIN for v4 v5 and v6)
TONE = MIN, 5, MAX.
VOLUME = MAX
The above-described setting, is and a recommended setting for achieve a maximum depth of detection.
General conclusion for BLISSTOOL LTC64X (THE BEAST) v6: Compared to v5 of THE BEAST, v6 provides better work at heavy terrain conditions, such as: highly mineralized terrains, terrains with a high content of ore, highly contaminated with iron terrains, highly mineralized sands, but also better depth of detection at low and medium mineralized terrains. These parameters can only be achieved with precision adequate setting from users with a very good knowledge for the metal detector and the hobby metal detecting as a whole. With medium levels of setting, v6 has parameters very similar to v5. Therefore v6 is recommended only for VERY EXPERIENCED users, which have the necessary knowledge and skills to make the most of the power of THE BEAST v6 and which want to have the BLISSTOOL metal detector with the best depth of detection until now. For BEGINNERS, INTERMEDIATE and EXPERIENCED users, more suitable are v4 and v5.
Photos of BLISSTOOL LTC64X (THE BEAST) v6, are available in the following galleries in BLISSTOOL GALLERIES:
http://blisstool.in/index.php/en/category/81
http://blisstool.in/index.php/en/category/80
http://blisstool.in/index.php/en/category/79
Field tests of BLISSTOOL LTC64X (THE BEAST) v6, are available in YouTube channel BLISSTOOL:
http://www.youtube.com/user/blisstool/videos
Complex parallel tests of BLISSTOOL LTC64X (THE BEAST) v6 with other brands metal detectors, are available in YouTube channel BLISSTOOLVERSUS:
http://www.youtube.com/user/blisstoolversus/videos
BLISSTOOL LTC64X (THE BEAST) v6 is available for the market and can be purchased from BLISSTOOL manufacturer and from the authorized BLISSTOOL distributors.
Statistics: Posted by BLISSTOOL — Wed Nov 26, 2014 5:49 pm
]]>
As a developer of metal detector BLISSTOOL LTC64X (THE BEAST), below I provide essential information representing summarized my response to numerous similar user questions.
I hope it is useful to you.
Please note that when you lower all settings of metal detector BLISSTOOL LTC64X, for example: GAIN = MIN, THRESHOLD = MIN, or close to these settings, its depth of detection is equal to the depth of detection of typical high-end detector from another brand, but with this setup it surpasses them as stability, has easy ground balance, excellent discrimination and excellent detection speed and recovery speed. Set your BLISSTOOL LTC64X detector in this way and it will be excellent turn-on and go detector. Will be completely stable and will work generally with random settings everywhere, ie will tolerate high tolerance settings and will not require fine tuning for each terrain.
Everything up, ie GAIN = 1 - 3 - 5 - MAX, THRESHOLD = 3 - 5 - 6.8, provides significantly greater depth of detection of THE BEAST, in some cases two to three times more in comparison to other brands detectors with the same size search coil, and even reaches outside the area of discrimination.
Each IB/VLF detector discriminates successfully in the ground to a maximum depth equal approximately to the size (the diameter) of its search coil. Most detectors detect coin near to this depth, ie maximum up to about 15 - 30 cm, ie 6 - 12 inches, but BLISSTOOL LTC64X detect coin to a depth up to 40 - 58 cm maximum, ie up to 16 - 23 inches, and in this connection it might also detect iron in such great depth, but THE BEAST has all the necessary settings to ignore even such deep irons, as far as possible purely theoretical and scientific.
Furthermore, the maximum depth of the quality discrimination for all detectors, is very much dependent on the characteristics of the soil and the characteristics of the iron object (composition, size, shape, orientation in the soil).
All BLISSTOOL LTC64X versions (v2, v2i, v3, v4, v5) have qualitative discrimination of iron, as the new v4 and v5 of THE BEAST have more improvements in this and other areas.
For discrimination of nails, the settings are: DISCRIMINATOR = III, DISCR LEVEL = 4 - 6, DISCR DEPTH = 8.8 - 10, with adjustment within this range according to the specific needs. If the soil is highly mineralized, or if there are many small iron wires, small nails and very small iron sheets, then proceed otherwise: set the detector in mode for highly mineralized soil, ie GROUND COARSE = about 7 - 8. It is close to the settings for ground balance to ferrite, so you can ground balance the detector directly to a piece of ferrite, and if needed (depending on the soil) to decreases its sensitivity (from potentiometers GAIN and THRESHOLD) to no false signals from the terrain. With this setup, the detector ignores iron oxides and small irons, as small nails and small iron sheets on the ground, without the need to increase its discrimination from potentiometers DISCL LEVEL and DISCR DEPTH. If you do not have a piece of ferrite, just set the settings GROUND MODE = MAN, GROUND COARSE = 8 and reduce or increase potentiometer GROUND COARSE by 0.5 - 1.0 level to achieve the desired result.
Technically, if the user dig iron with BLISSTOOL LTC64X, without want it, this is a signal that the detector is set incorrectly by the user, no matter how much experience the user has with other brands detectors.
BLISSTOOL LTC64X is not ordinary detector, it is simply THE BEAST. Its purpose is not turn-on and go detector, although in version 4 and 5 its "taming" is easy even for beginners.
Must not forget that BLISSTOOL LTC64X (THE BEAST) provides a depth of detection which is still in the field of science fiction for most other brands detectors and this has a price, it is not a free, ie as need of its adequate and precise user setting, real experience with it, etc.
Best Regards,
Ahmed Merchev
(President, sole owner and chief developer of BLISSTOOL)
BLISSTOOL
www.blisstool.com
info@blisstool.com
+359883450667
Statistics: Posted by BLISSTOOL — Mon Oct 06, 2014 3:07 pm
]]>
SECOND ADDITION to DETAILED REPORT for the improvements and the new features of v4 and v5 of BLISSTOOL LTC64X (THE BEAST).
IMPORTANT: This article contains extensive additional information about all the improvements and new features of v4 and v5 of BLISSTOOL LTC64X (THE BEAST). If you are interested in v4 and v5, it is strongly recommended to get acquainted in detail with all the information available below.
/01/ ADDITION about the differences in the depth of detection of the different versions:
In a medium mineralized terrain, the maximum depth of detection of a coin with a diameter 24 mm, for the different versions of BLISSTOOL LTC64X (THE BEAST), with 28 cm (11") DD search coil, is:
- for v2 = 40 cm (15.7")
- for v2i = 43 cm (16.9")
- for v3 = 45 cm (17.7")
- for v4 = 52 cm (20.4") in mode NORMAL / 58 cm (22.8") in mode TURBO/BOOST.
- for v5 = 52 cm (20.4") in mode NORMAL, AUTO ZONES = III / 58 cm (22.8") in mode TURBO/BOOST, AUTO ZONES = III.
The depths of detection, described above, especially for v4 and v5, are achieved and in SILENT mode of the metal detector, i.e. without audio threshold (THRESHOLD set to level just before the buzz).
The typical setting of the metal detector, at which are achieved the above described maximum depths of detection, is:
GROUND MODE = MAN
GROUND COARSE = 4 - 6
GROUND FINE = 5
AUTO ZONES = III (only for v5)
GAIN = MAX
THRESHOLD = 6.0 - 6.8
SILENCER = OFF - 2
DISCRIMINATOR = III
DISCR LEVEL = 4 - 5
DISCR DEPTH = 8.0 - 8.5 - 8.8
FREQUENCY = MAX (and also MIN for v4 and v5)
TONE = MIN, 5, MAX.
VOLUME = MAX
The above-described setting, is and a recommended setting for achieve a maximum depth of detection.
/02/ Recommended settings when getting started, immediately after the purchase, of metal detector BLISSTOOL LTC64X (THE BEAST):
In getting started, immediately after the purchase, of metal detector BLISSTOOL LTC64X (THE BEAST), regardless of its version, the following settings are recommended:
In auto ground balance mode and low sensitivity:
GROUND MODE = AUTO
AUTO ZONES = II (and if necessary III or I, depending on the terrain)
GAIN = MIN - 3
THRESHOLD = 5.0
SILENCER = 2
DISCRIMINATOR = III
DISCR LEVEL = 5
DISCR DEPTH = 8.8 - 9.0
FREQUENCY = MAX
TONE = MIN or MAX
VOLUME = MAX
In manual ground balance mode and low sensitivity:
GROUND MODE = MAN
GROUND COARSE = about 5 (depending on the terrain)
GROUND FINE = 5
AUTO ZONES = III (only for v5)
GAIN = MIN - 3
THRESHOLD = 5.0
SILENCER = 2
DISCRIMINATOR = III
DISCR LEVEL = 5
DISCR DEPTH = 8.8 - 9.0
FREQUENCY = MAX
TONE = MIN or MAX
VOLUME = MAX
The above mentioned settings, are especially suitable for beginners and are applicable to at least 80% of the terrains.
/03/ Rejection of hot rocks from metal detector BLISSTOOL LTC64X (THE BEAST):
Metal detector BLISSTOOL LTC64X (THE BEAST) is designed to be effective on all types of terrains, including medium and highly mineralized terrains, terrains with a high content of ore and terrains dotted with stones and rocks, slag, hot rocks and ceramics.
In all versions of THE BEAST, for effective rejection of hot rocks, is recommended:
- work in manual ground balance mode (GROUND MODE = MAN) and manual ground balancing of the metal detector (with potentiometers GROUND COARSE and GROUND FINE), not to the ground, but directly on a piece of hot rock (placed on the ground) up to its rejection . The same method is applied and for manual ground balancing to ceramics, stones and rocks.
- work in automatic ground balance mode (GROUND MODE = AUTO), AUTO ZONES = III.
For hot rocks, containing ferrous metals and their oxides (for example: iron and iron oxides), the manual ground balance is done in mode "All metal", i.e. with off discrimination of the metal detector (DISCR LEVEL = 0, DISCR DEPTH = 0). After the manual ground balancing on the hot rock, are set the user-selected levels of discrimination (for example: DISCR LEVEL = 4 - 5, DISCR DEPTH = 8.5 - 9.0).
For hot rocks containing non-ferrous metals and their oxides, because of their presence, usually manual ground balance in mode "All metal", i.e. with off discrimination of the metal detector (DISCR LEVEL = 0, DISCR DEPTH = 0) is not possible. In this case, the manual ground balance is performed with prior set discrimination of the metal detector (for example: DISCR LEVEL = 4 - 5, DISCR DEPTH = 8.5 - 9.0).
In most cases, the setting for rejection of hot rocks, coincides with the setting for ground balance to ferrite and with the setting for work on highly mineralized terrains.
/04/ Settings for ground balance to ferrite of the different versions of BLISSTOOL LTC64X (THE BEAST):
The settings for ground balance to ferrite, usually are particularly effective and are recommended as the base setting at: highly mineralized terrains, terrains with a high content of ore, terrains dotted with stones and rocks, slag, hot rocks, and terrains highly contaminated with small pieces of strong rotten (rusted) iron wires and iron sheets.
Settings for ground balance to ferrite of BLISSTOOL LTC64X (THE BEAST), all versions (v1, v2, v2i, v3, v4, v5):
In manual ground balance mode and low sensitivity:
GROUND MODE = MAN
GROUND COARSE = 8 (for v1, v2, v2i, v3; and v4 and v5 in mode TURBO/BOOST)
GROUND COARSE = 7 (for v4 and v5 in mode NORMAL)
GROUND FINE = 5
AUTO ZONES = III (only for v5)
GAIN = 3
THRESHOLD = 5.0 - 6.5
SILENCER = OFF - 2
DISCRIMINATOR = III
DISCR LEVEL = 4 - 5
DISCR DEPTH = 8.0 - 8.5 - 8.8
FREQUENCY = MAX (for v1, v2, v2i, v3; and v4 and v5 = mode NORMAL)
FREQUENCY = MIN (for v4 and v5 = mode TURBO/BOOST)
TONE = MIN or MAX
VOLUME = MAX
In manual ground balance mode and medium sensitivity:
GROUND MODE = MAN
GROUND COARSE = 7.2 - 7.5 (for v1, v2, v2i, v3; and v4 and v5 in mode TURBO/BOOST)
GROUND COARSE = 6.2 - 6.5 (for v4 and v5 in mode NORMAL)
GROUND FINE = 5
AUTO ZONES = III (only for v5)
GAIN = 5
THRESHOLD = 5.0 - 6.5
SILENCER = OFF - 2
DISCRIMINATOR = III
DISCR LEVEL = 4 - 5
DISCR DEPTH = 8.0 - 8.5 - 8.8
FREQUENCY = MAX (for v1, v2, v2i, v3; and v4 and v5 = mode NORMAL)
FREQUENCY = MIN (for v4 and v5 = mode TURBO/BOOST)
TONE = MIN or MAX
VOLUME = MAX
In manual ground balance mode and high sensitivity:
GROUND MODE = MAN
GROUND COARSE = 6.0 - 6.2 (for v1, v2, v2i, v3; and v4 and v5 in mode TURBO/BOOST)
GROUND COARSE = 5.0 - 5.2 (for v4 and v5 in mode NORMAL)
GROUND FINE = 5
AUTO ZONES = III (only for v5)
GAIN = MAX
THRESHOLD = 5.0 - 6.5
SILENCER = OFF - 2
DISCRIMINATOR = III
DISCR LEVEL = 4 - 5
DISCR DEPTH = 8.0 - 8.5 - 8.8
FREQUENCY = MAX (for v1, v2, v2i, v3; and v4 and v5 = mode NORMAL)
FREQUENCY = MIN (for v4 and v5 = mode TURBO/BOOST)
TONE = MIN or MAX
VOLUME = MAX
In automatic ground balance mode and from medium to high sensitivity:
GROUND MODE = AUTO
AUTO ZONES = III
GAIN = 6 (for v1, v2, v2i, v3; and v4 and v5 in mode NORMAL)
GAIN = 9 (for v4 and v5 in mode TURBO/BOOST)
THRESHOLD = 5.0 - 6.5
SILENCER = OFF - 2
DISCRIMINATOR = III
DISCR LEVEL = 4 - 5
DISCR DEPTH = 8.0 - 8.5 - 8.8
FREQUENCY = MAX (for v1, v2, v2i, v3; and v4 and v5 = mode NORMAL)
FREQUENCY = MIN (for v4 and v5 = mode TURBO/BOOST)
TONE = MIN or MAX
VOLUME = MAX
Depending on the specific conditions, the above-described settings can vary, generally in a small extent (with about 0.2 - 0.5 levels), so that, if necessary, the user can optimize them.
Statistics: Posted by BLISSTOOL — Sat May 24, 2014 10:36 pm
]]>
FIRST ADDITION to DETAILED REPORT for the improvements and the new features of v4 and v5 of BLISSTOOL LTC64X (THE BEAST).
IMPORTANT: This article contains extensive additional information about all the improvements and new features of v4 and v5 of BLISSTOOL LTC64X (THE BEAST). If you are interested in v4 and v5, it is strongly recommended to get acquainted in detail with all the information available below.
/01/ FIRST ADDITION about potentiometer FREQUENCY of v4 and v5:
With setting FREQUENCY = MAX, v4 and v5 work with base operating frequency 8.0KHz and NORMAL mode of the transmitter.
With setting FFREQUENCY = MIN, v4 and v5 work with base operating frequency 7.4KHz and TURBO/BOOST mode of the transmitter.
Mode TURBO/BOOST is designed to be used as a search mode in itself, similar of the mode NORMAL. Not recommended switching between the two modes (NORMAL and TURBO/BOOST), in order to further examination of the detected metal object, because in a manual ground balance mode (GROUND MODE = MAN), the switching between the two modes, requires a new setting of the ground balance of the metal detector. The difference in the ground balance, is particularly noticeable at high levels of GAIN, and also at medium and highly mineralized terrains, terrains with a high content of ore and terrains dotted with stones and rocks. Therefore, switching between the two modes (NORMAL and TURBO/BOOST), in order to further examination of the detected metal object, is only effective at low mineralized terrains and when working with low levels of GAIN (GAIN = from MIN to 3).
Moreover, unlike other brands of metal detectors, the TURBO/BOOST mode of THE BEAST is designed to be completely stable and universal, like the mode NORMAL. However, due to the increased transmitted power of the transmitter, mode TURBO/BOOST is not recommended in damp and wet soils, as for such field conditions, mode NORMAL is most suitable.
Because of the different transmitted power in mode NORMAL and in mode TURBO/BOOST of the transmitter:
- with a single charge of the LiPo battery, v1, v2 and v2i can work up to about 35 - 40 working hours;
- with a single charge of the LiPo battery, v3 can work up to about 30 - 35 working hours;
- with a single charge of the LiPo battery, v4 and v5 can work up to about 30 - 35 working hours in mode NORMAL and up to about 16 - 20 working hours in mode TURBO/BOOST of the transmitter with increased transmitted power.
Then, the battery needs to be recharged.
/02/ FIRST ADDITION about the automatic stabilizers available at v4 and v5:
v4 has permanently automatic stabilizer with a high degree of stabilization, but v5 has three automatic stabilizers (with low, medium and high degree of stabilization), which can be selected by a switch AUTO ZONES:
- AUTO ZONES = I = automatic stabilizer with a low degree of stabilization;
- AUTO ZONES = II = automatic stabilizer with a medium degree of stabilization;
- AUTO ZONES = III = automatic stabilizer with a high degree of stabilization.
In v3, at high levels of THRESHOLD in combination with high levels of GAIN, for example, when GAIN = MAX, and off silencer (SILENCER = OFF), i.e. with maximum sensitivity of the metal detector, in some terrains and specific terrain conditions, may occur the first signs of instability. Therefore, this mode is suitable only for more experienced users.
Unlike v3, v4 and v5 in an automatic stabilizer with a high degree of stabilization (AUTO ZONES = III), are completely stable even at GAIN = MAX, having an extreme depth of detection.
For best stability and best depth of detection, at v5, is recommended mode AUTO ZONES = III (automatic stabilizer with a high degree of stabilization).
With settings GROUND MODE = MAN, AUTO ZONES = III, at v5, usually achieves the best stability and best depth of detection.
Mode AUTO ZONES = III at v5, is suitable for about 80% of the terrains, as is particularly suitable and for beginners and for initial testing and learning of v5.
Moreover, at v5, usually, in AUTO ZONES = III versus AUTO ZONES = II, achieved with about 2 cm greater depth of detection for coins, and in AUTO ZONES = III versus AUTO ZONES = I, achieved with about 4 cm greater depth of detection for coins.
In v5, the recommended combinations between GAIN and AUTO ZONES, in a manual ground balance mode (GROUND MODE = MAN), are:
- At GAIN from MIN to 3, are recommended: AUTO ZONES = III, AUTO ZONES = II, AUTO ZONES = I;
- At GAIN from 4 to 6, are recommended: AUTO ZONES = III, AUTO ZONES = II;
- At GAIN from 7 to MAX, is recommended: AUTO ZONES = III.
In v5, the recommended combinations between the mineralization of the terrain and AUTO ZONES, in a manual ground balance mode (GROUND MODE = MAN), are:
- In low mineralized terrains (GROUND COARSE = from - to 3), are recommended: AUTO ZONES = III, AUTO ZONES = II, AUTO ZONES = I;
- In medium mineralized terrains (GROUND COARSE = from 4 to 6), are recommended: AUTO ZONES = III, AUTO ZONES = II;
- In highly mineralized terrains (GROUND COARSE = from 7 to +), is recommended: AUTO ZONES = III.
In v5, the recommended combinations between the contamination (granularity) of the terrain and AUTO ZONES, in a manual ground balance mode (GROUND MODE = MAN), are:
- In unpolluted terrains, are recommended: AUTO ZONES = III, AUTO ZONES = II, AUTO ZONES = I;
- In highly contaminated with iron and other pollutants terrains, are recommended: AUTO ZONES = III, AUTO ZONES = II;
- In terrains dotted with stones and rocks, slag, hot rocks, ceramics, is recommended: AUTO ZONES = III.
At v4 has only one automatic stabilizer (with a high degree of stabilization), but at v5, are available three automatic stabilizers (with low, medium and high degree of stabilization), to provide even greater versatility of the metal detector, as the various automatic stabilizers, influence not only of the overall stability and the depth of detection, but also of the base behavior of the metal detector:
- with an automatic stabilizer with a low degree of stabilization (AUTO ZONES = I), v5 has more aggressively, primary behavior of THE BEAST, as can hear all the nuances of the terrain. This mode is suitable for all users, but at high levels of GAIN, it is recommended only for very experienced users, who are able to distinguish all the specific nuances of the sound of the metal detector;
- with an automatic stabilizer with a medium degree of stabilization (AUTO ZONES = II), v5 has more moderate, semi tamed behavior of THE BEAST, as the field work is more comfortable. This mode is suitable for all users, but at high levels of GAIN, it is only recommended for intermediate and advanced users;
- with an automatic stabilizer with a high degree of stabilization (AUTO ZONES = III), v5 has totally stable, tamed behavior of THE BEAST, as the field work is much more comfortable. This mode is suitable for all users, including beginners, intermediate and advanced users. In this mode, even with GAIN = MAX, THE BEAST is completely stable and unconditionally obeys of the user.
Moreover, with an automatic stabilizer with a high degree of stabilization (available permanently in v4 and accessible in v5 with setting AUTO ZONES = III), due to the increased overall stability of the metal detector, at deeply buried metal objects, which are of the maximum possible depth of detection, the audio sound of the metal detector is extended, denser and more audible versus the mode with an automatic stabilizer with a medium degree of stabilization (available in v5 with setting AUTO ZONES = II) and mode with an automatic stabilizer with a low degree of stabilization (available in v5 with setting AUTO ZONES = I).
/03/ FIRST ADDITION about switch DISCRIMINATOR:
In all versions of THE BEAST, in mode DISCRIMINATOR = III, the maximum range of discrimination is limited to iron, aluminum foil and very small, low conductive metal objects, from non-ferrous metals and alloys. Therefore, mode DISCRIMINATOR = III is recommended for basic, universal search mode. Due to the limited up to aluminum foil discrimination, this mode is the safest and most effective at search of coins from different non-ferrous metals and their alloys: zinc, nickel, copper, lead, aluminum, silver, gold.
In v1, v2, v2i, v3, v4, all modes of switch DISCRIMINATOR (III, II, I) are suitable for basic search mode of metal objects from all non-ferrous metals and their alloys.
In v5, because of the extreme extended discrimination range, only mode DISCRIMINATOR = III is suitable for basic search mode of metal objects from all non-ferrous metals and their alloys. Modes DISCRIMINATOR = II and DISCRIMINATOR = I of v5, usually are not suitable for general search, because due to the extreme extended discrimination range at them, at high levels of DISCR LEVEL and DISCR DEPTH, can be rejected some small metal objects, as small bronze coins. These modes are suitable for specialized search of metal objects from specific non-ferrous metals and their alloys (for example: silver coins).
Furthermore, modes DISCRIMINATOR = II and DISCRIMINATOR = I of v5, in combination with mode DISCRIMINATOR = III, are particularly suitable for studying and understanding of the detected metal object even before it to be excavated.
Modes DISCRIMINATOR = II and DISCRIMINATOR = I of v5, are used and for distinguish (rejection) of various modern pollutants from aluminum, such as various aluminum caps, pull tabs of aluminum beverage cans, other aluminum packaging and boxes, and others.
Statistics: Posted by BLISSTOOL — Sat May 24, 2014 10:19 pm
]]>
DETAILED REPORT for the improvements and the new features of v4 and v5 of BLISSTOOL LTC64X (THE BEAST).
IMPORTANT: This article contains extensive information about all the improvements and new features of v4 and v5 of BLISSTOOL LTC64X (THE BEAST). If you are interested in v4 and v5, it is strongly recommended to get acquainted in detail with all the information available below.
Although in appearance, all versions look the same, they have significant differences in their characteristics: depth of detection, stability, discrimination, basic behavior. Therefore, each version must be considered for a different model metal detector, not a upgrade of the previous version.
The improvements and the new features of v4 and v5 of BLISSTOOL LTC64X (THE BEAST), are:
LTC64X v4 is better than v3, with that this LTC64X v4 is:
- with extreme improved depth of detection to very small, small, medium and large metal objects;
- with extremely improved stability, that is maintained even when using maximum settings;
- with two base operating frequencies: 8.0KHz and 7.4KHz;
- with smooth regulation of the operating frequency from 7.4KHz to 8.0KHz;
- with smooth regulation of the transmitted power of the transmitter;
- with NORMAL (at frequency 8.0KHz) and TURBO/BOOST mode of the transmitter (at frequency 7.4KHz) with increased transmitted power;
- TURBO/BOOST mode of the transmitter, effective not only at low mineralized terrains, but also in medium and highly mineralized terrains, terrains with a high content of ore and terrains dotted with stones and rocks;
- with an automatic stabilizer with a high degree of stabilization;
- with improved discrimination;
- with improved elimination of the inhomogeneities of the field;
- with improved rejection of iron, slag and hot rocks;
- with improved elimination of electromagnetic interferences;
- with behavior providing a more comfortable work in any type of terrain, including highly mineralized terrains, terrains with a high content of ore and terrains dotted with stones and rocks.
LTC64X v5 is better than v4, with that this LTC64X v5 is:
- with extreme extended discrimination range. Besides iron, aluminum foil and low conductive metal objects from non-ferrous metals and alloys, if necessary, can discriminate and medium and high conductive metal objects from non-ferrous metals (zinc, nickel, copper, lead, aluminum, silver, gold) and their alloys;
- with improved distribution of the three areas for discrimination, providing possibility for effective study and understanding of the detected metal object even before it to be excavated. Thanks to this, with high probability, can assume what exactly is the detected metal object even before it to be excavated: small, large, low quality, high quality, low, medium or high conductive. Moreover, for specific terrains and conditions, which the user is acquainted, can be assumed and from what kind of metal is the detected metal object: zinc, nickel, copper, lead, aluminum, silver, gold; and what exactly is the detected metal object: coin, artifact, treasure or modern pollutant. All this, provides a more effective and more convenient selective search of metal objects;
- with three automatic stabilizers (with low, medium and high degree of stabilization), providing the opportunity for highly effective stabilization and extreme performance in all field conditions.
v4 and v5 have the same knobs and switches as v3, v2i, v2 and v1, but because of the many improvements and new features of v4 and v5, their potentiometer FREQUENCY (for v4 and v5) and switch AUTO ZONES (only for v5) have a dual function, i.e. they have a second, additional function, only available in v4 and v5.
Thanks to this second, additional function of potentiometer FREQUENCY and switch AUTO ZONES, at v4 and v5, in an elegant way, there is provided a quick and convenient access to the new features available in v4 and v5, without the need of adding other knobs and switches.
Moreover, v5 is with extreme extended discrimination range and with improved distribution of the three areas for discrimination, selectable by switch DISCRIMINATOR.
The main differences in the control and the power of v4 and v5 of BLISSTOOL LTC64X (THE BEAST), compared to v3, v2i, v2, v1, are:
[01] Potentiometer FREQUENCY:
- At v3, v2i, v2 and v1, potentiometer FREQUENCY has only one function:
/1/ Change of the operating frequency of the metal detector in range +-60Hz, in order to avoid external electromagnetic interferences. The metal detector always work in NORMAL mode of the transmitter with normal transmitted power. The basic operating frequency of the metal detector is just one: 8.0KHz for v3, v2i, v2, and 8.5KHz for v1.
- At v4 and v5, potentiometer FREQUENCY has two functions:
/1/ Change of the operating frequency of the metal detector in range +-600Hz, in order to avoid external electromagnetic interferences and/or in order to switch between the two base operating frequencies: 8.0KHz and 7.4KHz. With setting FREQUENCY = MAX, the metal detector works with base operating frequency 8.0KHz, but with setting FREQUENCY = MIN, the metal detector works with base operating frequency 7.4KHz. By turning the potentiometer FREQUENCY from level MAX to level MIN, provides smooth regulation of the operating frequency from 8.0KHz to 7.4KHz;
/2/ Switch between NORMAL and TURBO/BOOST mode of the transmitter and smooth regulation of the transmitted power of the transmitter: with setting FREQUENCY = MAX, the metal detector works in NORMAL mode of the transmitter, i.e. with normal transmitted power, but with setting FREQUENCY = MIN, the metal detector works in TURBO/BOOST mode of the transmitter, i.e. with increased transmitted power. By turning the potentiometer FREQUENCY from level MAX to level MIN, provides smooth regulation of the transmitted power of the transmitter from NORMAL to TURBO/BOOST power.
Because of the combination in v4 and v5 of the above-described two functions of potentiometer FREQUENCY:
- with setting FREQUENCY = MAX, v4 and v5 work with base operating frequency 8.0KHz and NORMAL mode of the transmitter with normal transmitted power;
- with setting FFREQUENCY = MIN, v4 and v5 work with base operating frequency 7.4KHz and TURBO/BOOST mode of the transmitter with increased transmitted power;
- by turning the potentiometer FREQUENCY from level MAX to level MIN, provides smooth regulation of the operating frequency from 8.0KHz to 7.4KHz and of the transmitted power of the transmitter from NORMAL to TURBO/BOOST power;
- by turning the potentiometer FREQUENCY from level MIN to level MAX, provides smooth regulation of the operating frequency from 7.4KHz to 8.0KHz and of the transmitted power of the transmitter from TURBO/BOOST to NORMAL power.
Usually, mode TURBO/BOOST provides several centimeters better depth of detection versus mode NORMAL. Moreover, in TURBO/BOOST mode, the metal detector is more resistant to external electromagnetic interferences.
When working in a manual ground balance mode (switch GROUND MODE = MAN), if changing the setting of potentiometer FREQUENCY, is necessary a new manual setting of the ground balance via potentiometers GROUND COARSE and GROUND FINE. It is necessary to increase the level, as typically, the offset is with maximum 1 - 1.5 - 2 levels. For example, if with a setting FREQUENCY = MAX, the metal detector is balanced to the ground at GROUND COARSE = 5.0 and GROUND FINE = 5.0, follows that with a setting FREQUENCY = MIN, for the same terrain, the metal detector will have balance to the ground at GROUND COARSE = about 6.5 and GROUND FINE = 5.0. For low mineralized terrains, this difference is usually negligible, but for medium and highly mineralized terrains, it is significant and should be considered.
The TURBO/BOOST mode of v4 and v5, is effective not only at low mineralized terrains, but also in medium and highly mineralized terrains, terrains with a high content of ore and terrains dotted with stones and rocks. However, due to the increased transmitted power in TURBO/BOOST mode, in medium and highly mineralized terrains, terrains with a high content of ore and terrains dotted with stones and rocks, the manual ground balance may be more difficult to achieve, than in mode NORMAL. In such terrains, the manual ground balance in mode TURBO/BOOST, is still relatively easily attainable, but the setting should be done more carefully and more precisely by the user. For this purpose, after the basic setup of the ground balance from potentiometer GROUND COARSE, is very convenient the use of a potentiometer GROUND FINE for additional, fine tuning.
In some terrains, for example in highly mineralized terrains, terrains with a high content of ore and terrains dotted with stones and rocks, and especially in heavy specific field conditions, the TURBO/BOOST mode instead providing of a greater depth of detection, may have the opposite effect. Therefore, in v4 and v5 are available for selection by the user the two modes: mode NORMAL and mode TURBO/BOOST. It provides an opportunity for excellent depth of detection in all field conditions.
[02] Switch AUTO ZONES:
- At v4, v3, v2i, v2 and v1, switch AUTO ZONES has only one function:
/1/ To set one of the three available automatic ground zones at work in automatic ground balance mode (switch GROUND MODE = AUTO). In manual ground balance mode (switch GROUND MODE = MAN), this function of switch AUTO ZONES not working.
- At v5, switch AUTO ZONES has two functions:
/1/ Function identical to its function in v4, v3, v2i, v2 and v1, i.e. to set one of the three available automatic ground zones at work in automatic ground balance mode (switch GROUND MODE = AUTO). In manual ground balance mode (switch GROUND MODE = MAN), this function of switch AUTO ZONES not working;
/2/ Switching between the three automatic stabilizers available in v5, as this its function work in auto ground balance mode (switch GROUND MODE = AUTO), and also in manual ground balance mode (switch GROUND MODE = MAN):
- with setting: AUTO ZONES = I, v5 work with an automatic stabilizer with a low degree of stabilization;
- with setting: AUTO ZONES = II, v5 work with an automatic stabilizer with a medium degree of stabilization;
- with setting: AUTO ZONES = III, v5 work with an automatic stabilizer with a high degree of stabilization.
Unlike v5, which has three automatic stabilizers (with low, medium and high degree of stabilization), which can be selected by a switch AUTO ZONES, v4 has only one automatic stabilizer (with a high degree of stabilization), as it always works with it, i.e. therefore is not necessary its switching, switch AUTO ZONES at v4, has only one function, as at v3, v2i, v2 and v1.
Because of the combination in v5 of the above-described two functions of switch AUTO ZONES:
- with settings: GROUND MODE = AUTO, AUTO ZONES = I, the metal detector work in automatic ground balance mode, with an automatic ground zone I and an automatic stabilizer with a low degree of stabilization. Automatic ground zone I is optimized for low mineralized terrains, for which an automatic stabilizer with a low degree of stabilization is completely sufficient;
- with settings: GROUND MODE = AUTO, AUTO ZONES = II, the metal detector work in automatic ground balance mode, with an automatic ground zone II and an automatic stabilizer with a medium degree of stabilization. Automatic ground zone II is optimized for medium mineralized terrains, for which an automatic stabilizer with a medium degree of stabilization is completely sufficient;
- with settings: GROUND MODE = AUTO, AUTO ZONES = III, the metal detector work in automatic ground balance mode, with an automatic ground zone III and an automatic stabilizer with a high degree of stabilization. Automatic ground zone III is optimized for highly mineralized terrains, for which an automatic stabilizer with a high degree of stabilization is completely sufficient;
- with settings: GROUND MODE = MAN, AUTO ZONES = I, the metal detector work in manual ground balance mode and an automatic stabilizer with a low degree of stabilization;
- with settings: GROUND MODE = MAN, AUTO ZONES = II, the metal detector work in manual ground balance mode and an automatic stabilizer with a medium degree of stabilization;
- with settings: GROUND MODE = MAN, AUTO ZONES = III, the metal detector work in manual ground balance mode and an automatic stabilizer with a high degree of stabilization.
The automatic stabilizers available in v4 and v5, providing extreme improving of the stability of THE BEAST, as high stability is maintained even when using maximum settings, especially in mode with a stabilizer with a high degree of stabilization (available permanently in v4 and available in v5 with a setting AUTO ZONES = III). Moreover, the improving of the stability, leads and to an improving of the depth of detection.
[03] Switch DISCRIMINATOR:
The DISCRIMINATOR switch, for all versions, serves to set the maximum range of discrimination of the metal detector, ie it defines the scope of potentiometer DISCR LEVEL. The various modes are conditional numbered as: "I", "II" and "III".
- At v4, v3, v2i, v2 and v1:
- In mode DISCRIMINATOR = III, the maximum range of discrimination is limited to iron, aluminum foil and very small, low conductive metal objects, from non-ferrous metals and alloys;
- In mode DISCRIMINATOR = II, the maximum range of discrimination is limited to small, low conductive metal objects, mainly from the following non-ferrous metals and their alloys: zinc, nickel, copper;
- In mode DISCRIMINATOR = I, the maximum range of discrimination is limited to small, high conductive metal objects, mainly from the following non-ferrous metals and their alloys: zinc, nickel, copper, lead, aluminum.
- At v5:
- In mode DISCRIMINATOR = III, the maximum range of discrimination is limited to iron, aluminum foil and very small, low conductive metal objects, from non-ferrous metals and alloys;
- In mode DISCRIMINATOR = II, the maximum range of discrimination is limited to medium, high conductive metal objects, mainly from the following non-ferrous metals and their alloys: zinc, nickel, copper, lead, aluminum.
- In mode DISCRIMINATOR = I, the maximum range of discrimination is limited to large, high conductive metal objects, mainly from the following non-ferrous metals and their alloys: zinc, nickel, copper, lead, aluminum, silver, gold.
Given the above available information for switch DISCRIMINATOR:
- Mode DISCRIMINATOR = III is the same for all versions (v5, v4, v3, v2i, v2 and v1);
- Mode DISCRIMINATOR = II of v5, is with about 25% larger than the largest range, i.e. mode DISCRIMINATOR = I, of v4, v3, v2i, v2 and v1. Therefore, mode DISCRIMINATOR = II of v5, is very similar to the mode DISCRIMINATOR = I of v4, v3, v2i, v2 and v1;
- Mode DISCRIMINATOR = I of v5, is several times larger than the largest range, i.e. mode DISCRIMINATOR = I, of v4, v3, v2i, v2 and v1. Therefore, v5 has extreme extended discrimination range.
The extreme extended discrimination range and the improved distribution of the three areas for discrimination at v5, providing possibility for effective study and understanding of the detected metal object even before it to be excavated. For this purpose, the user must explore intentionally, the detected metal object at various modes of switch DISCRIMINATOR: III, II and I. This is done by easily and quickly manual switching between them (from switch DISCRIMINATOR). Depending on what exactly is the detected metal object, in some modes it will be detected, while in others will be rejected. For starters, the exploration (the study) is carried out without changing the current levels of potentiometers DISCR LEVEL and DISCR DEPTH, as only if need additional orientation, can be applied study at higher levels of DISCR LEVEL and DISCR DEPTH.
Thanks to the above described method, at v5, with high probability, can assume what exactly is the detected metal object even before it to be excavated: small, large, low quality, high quality, low, medium or high conductive. Moreover, for specific terrains and conditions, which the user is acquainted, can be assumed and from what kind of metal is the detected metal object: zinc, nickel, copper, lead, aluminum, silver, gold; and what exactly is the detected metal object: coin, artifact, treasure or modern pollutant. All this, provides a more effective and more convenient selective search of metal objects.
An example for the above-described method for effective study and understanding of the detected metal object even before it to be excavated:
Introduction: The user works with v5 on medium mineralized terrain in discrimination mode with settings: DISCRIMINATOR = III, DISCR DEPTH = 9, DISCR LEVEL = 6. The user detects with the metal detector (on DISCRIMINATOR = III), a clear signal from non-ferrous metal (as at these settings the metal detector rejected iron):
- If in mode DISCRIMINATOR = II and in mode DISCRIMINATOR = I, the object is still detected, follows that the detected metal object is probably a silver coin;
- If in mode DISCRIMINATOR = II the object is still detected, but in mode DISCRIMINATOR = I the object is rejected, follows that the detected metal object is probably an aluminum cap;
- If in mode DISCRIMINATOR = II and in mode DISCRIMINATOR = I, the object is rejected, follows that the detected metal object is probably a bronze coin.
The settings and the assumptions described in the example above are examples only, but for a specific terrain, the user of v5, relatively easy can find such combinations, which in practice to do a good job for his particular terrain and for the specific metal objects which are most often detected there.
General conclusion for BLISSTOOL LTC64X (THE BEAST): Compared to the previous versions, v4 and v5 of THE BEAST, have many improvements and new features, which make them an excellent choice for top metal detector. However, even the oldest version available for sale (v2), there are parameters, that are only dreams for many other metal detectors, especially on the depth of detection for coins. So, regardless of which version of THE BEAST you decide to purchase, or no matter what version of THE BEAST you currently have, you can be confident and proud that you have top metal detector with extreme depth of detection. But, if you want to have the best so far, v4 and v5 are the best choice.
Statistics: Posted by BLISSTOOL — Sun May 18, 2014 7:04 pm
]]>
Why not end the production of the older versions of THE BEAST, in the presence of its new versions?
- We not end the production of the older versions of THE BEAST, in the presence of its new versions, because each version has unique parameters, which allow to sell them separately and simultaneously, as different models metal detectors: with different prices and even in different price range, but with one thing in common: extreme depth of detection.
Although in appearance, all versions look the same, they have significant differences in their characteristics: depth of detection, stability, discrimination, basic behavior. Therefore, each version must be considered for a different model metal detector, not a upgrade of the previous version. For the same reason, the different versions have different prices, fall in different price range and are offered as different models metal detectors. Not available update from one to another version, i.e. from one model to another model metal detector, because this is associated with a complex and complicated changes in the electronics, which in some cases are even impossible to implement. Updates are possible, only within the same version, where such are available for it.
So far, BLISSTOOL LTC64X (THE BEAST) is available in six versions: v1, v2, v2i, v3, v4, v5.
To date 16.05.2014, from them are produce and sell: v2, v2i, v3, v4, v5. Only v1 has long been discontinued and no longer available, because it was completely replaced by v2.
All other versions are still produced and sold at the same time, as each has parameters which in some cases are only dream for other brands of metal detectors, i.e. all versions available for sale, continue to be competitive in terms of metal detectors from other brands.
For example, all versions of THE BEAST are particularly suitable for searching of coins and relics, as the depth of detection for coins, of all of them, is not offered by other brands in this price range, as some other brands do not even offer anything close as depth of detection, especially when working on medium and high mineralized terrains.
Real, metal detector BLISSTOOL LTC64X is one of the best deep detecting metal detectors in the world, especially when it comes to no resonance metal detectors type induction balance.
The simultaneous presence on the market of several versions of THE BEAST, actually creates confusion, given that the practice of many other brands of metal detectors, is to apply mainly cosmetic changes and to sell them as new models metal detectors. In contrast from them, we rely on pure demonstrable performance and efficiency. For example, we published official accurate data for the depth of detection on field of all our metal detectors and guarantee these parameters, as documenting our tests with video capture, and anytime, to anyone, we can prove over and over again in practice what we have said as parameters. There are very few manufacturers that do this. Why? Some users understand the answer to this question only after they buy a "high" class metal detector from another brand and understand the ugly truth, namely, that it really is a class "toys", i.e. "low" class as parameters, especially the parameter depth of detection, which for many users is the leading parameter.
For some consumers, because of human nature, this process of awareness is very painful. Initially, they are not willing to accept that gave their money away, or at least that their purchase did not justify their expectations. Even when they become familiar with the parallel field tests between BLISSTOOL and their metal detector from another brand, they again denied. Some of them even started negative campaigning against BLISSTOOL and develop various conspiracy theories, i.e. resort to self-deception, pure human reaction, as shock for them is really great.
This process of negative campaigns and denial, fueled mostly by agents and representatives of the other brands of metal detectors, as they defend primarily their market interest, regardless of the price. But in addition, there is also another objective reason: the depth of detection that provides THE BEAST, is much greater than the status quo, i.e. THE BEAST has drastic increased depth of detection compared to most other metal detectors from other brands. Therefore, viewed from the side, especially when the user has not tested in practice BLISSTOOL LTC64X, the guaranteed from us depth of detection, sounds like fiction. Therefore, the resistance against BLISSTOOL is so great. It got to the point, that even in some popular metal detecting forums, sponsored mainly by competing other brands of metal detectors, there is a complete media blackout about BLISSTOOL.
Our customers are primarily interested in the performance. For each version of THE BEAST, we offer something new, extra, which is provable and is not a cosmetic change, as even the oldest version available for sale (v2) there are parameters that are only dreams for some other brands metal detectors, especially on the depth of detection for coins.
Furthermore, ask yourself what in principle means the availability of a six versions of a specific product? This clearly indicates that the product and its platform are particularly promising and effective, as the product is greatly upgraded and improved, which is primarily in the interest of the customer. In this case, THE BEAST is tested continuously throughout the world, as from the feedback, in each new batch, we have and continue to make improvements within the same version, but the drastic differences and new functionalities as a result of our constant research activity, we present as a separate, new version.
If, despite my explanations, anyone still has any doubts about the power of THE BEAST, we challenge him on complex parallel tests, ie parallel field tests between THE BEAST and his metal detector from other brand. Such offer we make a public several years ago. Our only condition is to do video capture of all tests, then unlimited to publish and distribute them.
I hope this information is helpful to you.
With best wishes,
Ahmed Merchev
(President, sole owner and chief developer of BLISSTOOL)
BLISSTOOL
www.blisstool.com
info@blisstool.com
+359883450667
Statistics: Posted by BLISSTOOL — Fri May 16, 2014 12:28 pm
]]>
The differences in the depth of detection between the different versions of BLISSTOOL LTC64X (THE BEAST).
Metal detector BLISSTOOL LTC64X (THE BEAST) is available in six versions:
- version 1 (LTC64X v1, LTC64X version 1);
- version 2 (LTC64X v2, LTC64X version 2);
- version 2i (LTC64X v2i, LTC64X version 2i);
- version 3 (LTC64X v3, LTC64X version 3);
- version 4 (LTC64X v4, LTC64X version 4);
- version 5 (LTC64X version 5, LTC64X v5).
In terms of the depth of detection:
- In practice, when properly adjusted, v1 and v2 have the same depth of detection;
- v2i has better depth of detection of v1 and v2;
- v3 has better depth of detection of v1, v2 and v2i;
- In practice, when properly adjusted, v4 and v5 have the same depth of detection. v4 and v5 have better depth of detection of v1, v2, v2i and v3.
In practice, the differences in the depth of detection between the different versions of THE BEAST, with 28 cm (11") DD search coil, in soil with greater than medium degree of mineralization, are approximately the following:
For LTC64X v2i vs LTC64X v2:
- Compared with v2, v2i has from 3 to 5 cm greater depth of detection for coins. Most often about 3 cm;
- Compared with v2, v2i has from 5 to 10 cm greater depth of detection for small metal objects with size greater than that of the coins. Most often about 6 cm;
- Compared with v2, v2i has from 15 to 30 cm greater depth of detection for large metal objects.
For LTC64X v3 vs LTC64X v2i:
- Compared with v2i, v3 has from 3 to 5 cm greater depth of detection for coins. Most often about 3 cm;
- Compared with v2i, v3 has from 6 to 12 cm greater depth of detection for small metal objects with size greater than that of the coins. Most often about 8 cm;
- Compared with v2i, v3 has from 10 to 20 cm greater depth of detection for large metal objects.
For LTC64X v4 and LTC64X v5 vs LTC64X v3:
- Compared with v3, v4 and v5 have from 4 to 8 cm greater depth of detection for coins. Most often about 5 cm;
- Compared with v3, v4 and v5 have from 6 to 16 cm greater depth of detection for small metal objects with size greater than that of the coins. Most often about 10 cm;
- Compared with v3, v4 and v5 have from 15 to 25 cm greater depth of detection for large metal objects.
For LTC64X with 28 cm (11") DD search coil vs LTC64X with 38 cm (15") DD search coil, applies to all versions (v1, v2, v2i, v3, v4, v5):
- Compared with LTC64X with 28 cm (11") DD search coil, LTC64X with 38 cm (15") DD search coil has a greater depth of detection, from several centimeters for coins, to several tens of centimeters for large metal objects.
For LTC64X v4 and LTC64X v5 in NORMAL mode vs LTC64X v4 and LTC64X v5 in TURBO/BOOST mode:
- Compared with v4 and v5 in NORMAL mode, v4 and v5 in TURBO/BOOST mode have from 1 to 7 cm greater depth of detection for coins. Most often about 3 cm;
- Compared with v4 and v5 in NORMAL mode, v4 and v5 in TURBO/BOOST mode have from 8 to 16 cm greater depth of detection for large metal objects. Most often about 10 cm.
For LTC64X v5, depending on the automatic stabilizer:
- Compared with v5 in mode with an automatic stabilizer with a low degree of stabilization, v5 in mode with an automatic stabilizer with a medium degree of stabilization has from 1 to 3 cm greater depth of detection for coins. Most often about 2 cm;
- Compared with v5 in mode with an automatic stabilizer with a medium degree of stabilization, v5 in mode with an automatic stabilizer with a high degree of stabilization has from 1 to 3 cm greater depth of detection for coins. Most often about 2 cm;
- Compared with v5 in mode with an automatic stabilizer with a low degree of stabilization, v5 in mode with an automatic stabilizer with a high degree of stabilization has from 2 to 6 cm greater depth of detection for coins. Most often about 4 cm.
Statistics: Posted by BLISSTOOL — Thu May 15, 2014 5:40 pm
]]>
Metal detectors BLISSTOOL LTC64X (THE BEAST). Versions v1, v2, v2i, v3, v4, v5. Features and Differences.
Metal detector BLISSTOOL LTC64X (THE BEAST) is available in six versions:
- version 1 (LTC64X v1, LTC64X version 1);
- version 2 (LTC64X v2, LTC64X version 2);
- version 2i (LTC64X v2i, LTC64X version 2i);
- version 3 (LTC64X v3, LTC64X version 3);
- version 4 (LTC64X v4, LTC64X version 4);
- version 5 (LTC64X version 5, LTC64X v5).
The version of BLISSTOOL LTC64X is marked on the box with the electronic block of the metal detector.
Although in appearance, all versions look the same, they have significant differences in their characteristics: depth of detection, stability, discrimination, basic behavior. Therefore, each version must be considered for a different model metal detector, not a upgrade of the previous version. For the same reason, the different versions have different prices, fall in different price range and are offered as different models metal detectors. Not available update from one to another version, i.e. from one model to another model metal detector, because this is associated with a complex and complicated changes in the electronics, which in some cases are even impossible to implement. Updates are possible, only within the same version, where such are available for it.
As with every new batch, the parameters of all versions of BLISSTOOL LTC64X are improved, the metal detectors from the latest batches are better compared to the first presented batch: they have even greater depth of detection, even higher stability and are with even higher quality. To indicate this fact, all BLISSTOOL LTC64X metal detectors from the latest batches (i.e. all BLISSTOOL LTC64X metal detectors manufactured and sold after the date 12 May 2014), are labeled "THE BEAST" left and right of the box with the electronics block, as "THE BEAST", is now the official alias (nickname) of all versions of metal detector BLISSTOOL LTC64X. The BLISSTOOL LTC64X metal detectors with inscription "THE BEAST", include, guaranteed, all available improvements to date 12 May 2014 and beyond, when such are available.
LTC64X v1 is the standard version.
LTC64X v2 is a version specially adapted for heavy field conditions.
LTC64X v2i is an improved version of v2.
LTC64X v3 is a top version with extreme performance.
LTC64X v4 is a top version with extreme depth of detection, automatic stabilizer with a high degree of stabilization, NORMAL and TURBO/BOOST mode of the transmitter.
LTC64X v5 is a top version with extreme depth of detection, three automatic stabilizers (with low, medium and high degree of stabilization), NORMAL and TURBO/BOOST mode of the transmitter, extreme extended discrimination range and improved distribution of the three areas for discrimination (providing possibility for effective study and understanding of the detected metal object even before it to be excavated).
LTC64X v2 is better than v1 with that this LTC64X v2 is optimized to work on:
- highly contaminated terrains;
- highly mineralized terrains;
- terrains with a high content of ore.
Of the above described terrains, LTC64X v1 also works, but LTC64X v2 is additional optimized for such terrains.
LTC64X v2i is better than v2, with that this LTC64X v2i has improved:
- the depth of detection;
- the sensitivity to very small metal objects.
LTC64X v3 is better than v2i, with that this LTC64X v3 is:
- with extreme improved depth of detection;
- with extreme improved sensitivity to very small metal objects;
- optimized for Gold Nugget prospecting;
- with extended setup of the sensitivity and the behavior;
- with capable of successfully competing with multi-period pulse induction metal detectors. In comparison with them, has a similar depth of detection, greater universality and excellent discrimination.
LTC64X v4 is better than v3, with that this LTC64X v4 is:
- with extreme improved depth of detection to very small, small, medium and large metal objects;
- with extremely improved stability, that is maintained even when using maximum settings;
- with two base operating frequencies: 8.0KHz and 7.4KHz;
- with smooth regulation of the operating frequency from 7.4KHz to 8.0KHz;
- with smooth regulation of the transmitted power of the transmitter;
- with NORMAL (at frequency 8.0KHz) and TURBO/BOOST mode of the transmitter (at frequency 7.4KHz) with increased transmitted power;
- TURBO/BOOST mode of the transmitter, effective not only at low mineralized terrains, but also in medium and highly mineralized terrains, terrains with a high content of ore and terrains dotted with stones and rocks;
- with an automatic stabilizer with a high degree of stabilization;
- with improved discrimination;
- with improved elimination of the inhomogeneities of the field;
- with improved rejection of iron, slag and hot rocks;
- with improved elimination of electromagnetic interferences;
- with behavior providing a more comfortable work in any type of terrain, including highly mineralized terrains, terrains with a high content of ore and terrains dotted with stones and rocks.
LTC64X v5 is better than v4, with that this LTC64X v5 is:
- with extreme extended discrimination range. Besides iron, aluminum foil and low conductive metal objects from non-ferrous metals and alloys, if necessary, can discriminate and medium and high conductive metal objects from non-ferrous metals (zinc, nickel, copper, lead, aluminum, silver, gold) and their alloys;
- with improved distribution of the three areas for discrimination, providing possibility for effective study and understanding of the detected metal object even before it to be excavated. Thanks to this, with high probability, can assume what exactly is the detected metal object even before it to be excavated: small, large, low quality, high quality, low, medium or high conductive. Moreover, for specific terrains and conditions, which the user is acquainted, can be assumed and from what kind of metal is the detected metal object: zinc, nickel, copper, lead, aluminum, silver, gold; and what exactly is the detected metal object: coin, artifact, treasure or modern pollutant. All this, provides a more effective and more convenient selective search of metal objects;
- with three automatic stabilizers (with low, medium and high degree of stabilization), providing the opportunity for highly effective stabilization and extreme performance in all field conditions.
For all BLISSTOOL LTC64X versions are available:
- STANDARD package with 28 cm (11") DD search coil BLISSTOOL DD28SC2;
- DEEP package with 38 cm (15") DD search coil BLISSTOOL DD38SC2;
- EXTREME package with 28 cm (11") DD search coil BLISSTOOL DD28SC2 and 38 cm (15") DD search coil BLISSTOOL DD38SC2.
Which version is right for you to judge yourself according to your specific needs.
Our additional guide recommendations and clarification for you are:
1/ In terms of the terrain and the universality:
- All versions are designed to be universal, ie with adequate user setup, all versions work well on any type of terrains.
2/ In terms of the depth of detection:
- In practice, when properly adjusted, v1 and v2 have the same depth of detection;
- v2i has better depth of detection of v1 and v2;
- v3 has better depth of detection of v1, v2 and v2i;
- In practice, when properly adjusted, v4 and v5 have the same depth of detection. v4 and v5 have better depth of detection of v1, v2, v2i and v3.
In practice, the differences in the depth of detection between the different versions of THE BEAST, with 28 cm (11") DD search coil, in soil with greater than medium degree of mineralization, are approximately the following:
For LTC64X v2i vs LTC64X v2:
- Compared with v2, v2i has from 3 to 5 cm greater depth of detection for coins. Most often about 3 cm;
- Compared with v2, v2i has from 5 to 10 cm greater depth of detection for small metal objects with size greater than that of the coins. Most often about 6 cm;
- Compared with v2, v2i has from 15 to 30 cm greater depth of detection for large metal objects.
For LTC64X v3 vs LTC64X v2i:
- Compared with v2i, v3 has from 3 to 5 cm greater depth of detection for coins. Most often about 3 cm;
- Compared with v2i, v3 has from 6 to 12 cm greater depth of detection for small metal objects with size greater than that of the coins. Most often about 8 cm;
- Compared with v2i, v3 has from 10 to 20 cm greater depth of detection for large metal objects.
For LTC64X v4 and LTC64X v5 vs LTC64X v3:
- Compared with v3, v4 and v5 have from 4 to 8 cm greater depth of detection for coins. Most often about 5 cm;
- Compared with v3, v4 and v5 have from 6 to 16 cm greater depth of detection for small metal objects with size greater than that of the coins. Most often about 10 cm;
- Compared with v3, v4 and v5 have from 15 to 25 cm greater depth of detection for large metal objects.
For LTC64X with 28 cm (11") DD search coil vs LTC64X with 38 cm (15") DD search coil, applies to all versions (v1, v2, v2i, v3, v4, v5):
- Compared with LTC64X with 28 cm (11") DD search coil, LTC64X with 38 cm (15") DD search coil has a greater depth of detection, from several centimeters for coins, to several tens of centimeters for large metal objects.
For LTC64X v4 and LTC64X v5 in NORMAL mode vs LTC64X v4 and LTC64X v5 in TURBO/BOOST mode:
- Compared with v4 and v5 in NORMAL mode, v4 and v5 in TURBO/BOOST mode have from 1 to 5 cm greater depth of detection for coins. Most often about 3 cm;
- Compared with v4 and v5 in NORMAL mode, v4 and v5 in TURBO/BOOST mode have from 8 to 16 cm greater depth of detection for large metal objects. Most often about 10 cm.
For LTC64X v5, depending on the automatic stabilizer:
- Compared with v5 in mode with an automatic stabilizer with a low degree of stabilization, v5 in mode with an automatic stabilizer with a medium degree of stabilization has from 1 to 3 cm greater depth of detection for coins. Most often about 2 cm;
- Compared with v5 in mode with an automatic stabilizer with a medium degree of stabilization, v5 in mode with an automatic stabilizer with a high degree of stabilization has from 1 to 3 cm greater depth of detection for coins. Most often about 2 cm;
- Compared with v5 in mode with an automatic stabilizer with a low degree of stabilization, v5 in mode with an automatic stabilizer with a high degree of stabilization has from 2 to 6 cm greater depth of detection for coins. Most often about 4 cm.
Statistics: Posted by BLISSTOOL — Thu May 15, 2014 11:10 am
]]>
Direct links:
IMPORTANT: The versions of the User Guide by date 10.05.2014, 15:04 (version EN201405101504 and version BG201405101504) for metal detector BLISSTOOL LTC64X (THE BEAST), contain supplemented useful information about the proper fixation of the cable of the search coil, in order to avoid false signals, so we recommend you to review them!
The current English User Guide, contains additional information, mainly in the following sections (points) of the document:
- 7. Structure of the metal detector;
- 8. Assembling and disassembling of the metal detector.
We hope that this is helpful to you.
Statistics: Posted by BLISSTOOL — Sat May 10, 2014 12:46 pm
]]>
Direct links:
The versions of the User Guide by date 20.04.2014, 19:40 (version EN201404201940 and version BG201404201940) for metal detector BLISSTOOL LTC64X (THE BEAST), contain supplemented useful information about the setting of the metal detector, so we recommend that you review them.
The current English User Guide, contains additional information, mainly in the following sections (points) of the document:
- 4. Versions;
- 6.5. Search coils;
- 9.2. FREQUENCY potentiometer;
- 9.4. AUTO ZONES switch;
- 9.5. GROUND COARSE potentiometer;
- 9.6. GROUND FINELY potentiometer;
- 9.8. SILENCER potentiometer;
- 9.9. DISCRIMINATOR switch;
- 9.13. PHONES connector;
- 9.16. CHARGE connector;
- 9.17. GAIN potentiometer;
- 9.18. TONE potentiometer;
- 10. Sensitivity. Mode "Explosion" and mode "Waft". Mode without audio threshold (silent mode) and mode with audio threshold.;
- 13. Battery. Battery charging.
We hope that this is helpful to you.
Statistics: Posted by BLISSTOOL — Sun Apr 20, 2014 6:36 pm
]]>
Latest versions of the user guides for metal detector BLISSTOOL LTC64X (THE BEAST), are available on .
Direct links:
User Guides for metal detector BLISSTOOL LTC64X (THE BEAST):
Statistics: Posted by BLISSTOOL — Sun Apr 20, 2014 6:21 pm
]]>